General Specifications:
• Year Manufactured: 1986 (Upgraded with New AC to DC Drives)
• Material: Hot Rolled, Cold Rolled, Galvanized, Stainless
• Maximum Coil Weight: 60,000#
• Incoming Strip Width: 62"
• Outgoing Strip Width: 60"
• Minimum Strip Thickness: .010"
• Maximum Strip Thickness: .375"
• Incoming Coil ID: 19" to 20”, Up to 26" with Filler Pads (Nominal 20” ID)
• Outgoing Coil ID: 20" to 24", Up to 30” with Filler Pads (Nominal 20” ID)
• Maximum Coil OD: 76"
• Number of Cuts: 16 Cuts of .250” Mild Steel, 7 Cuts of .375”, 21 Cuts of .020” (Could do 20 Cuts of .250” with 55” OD Coils at Recoiler)
• Maximum Slitting Tension: 37,500#
• Maximum Line Speed: Heavy-Duty Two-Speed Gear Reducer 100 & 300 FPM with Coil Build Up to 1,000 FPM
• Electrical: Variable Speed, 250 kW at Peak Load, 460/3/60 Cycle or 380/3/50 Cycle Input
• Line Direction: Right to Left
Consisting of the Following:
Three Arm Turnstile, 60" Arms
Coil Car
44" Wide Deck, 18” Vertical Lift
Self-Contained Hydraulics
Platform Top "V" Saddle
Coil Car Traverse 15' by Hydraulic Orbit Motor Chain & Sprocket
64" Wide Uncoiler with Heavy Duty Twin Hold Down Rolls
19” to 20” ID Coils with Filler Pads for Up to 26” ID (Nominal 20” ID)
Sliding Base ± 6” from Centerline, Air Clutch
AC Motor Feed and Recoiling
Water Cooled Air Brake
Peeler System, In/Out, Up/Down
Powered Pinch Roll System, 66” Face
Hydraulic Shear for Cropping Heads & Tails of Coils
64" Wide x 10” Diameter Precision Arbor Slitter with Feed Up Drive, (2) Heads
Dog Clutch for Quick Head Removal
Shimless Tooling (See Details Below)
(2)-18” Wide x 42” OD Capacity Scrap Winders with Level Wind
Hydraulic Self Dump with Oscillating Eye
Hydraulically Actuated Threading Table
72" Wide Recoiler with Separator Shaft and Full Complement of Tooling
Two-Speed Gearbox
Hydraulic Gripper Slot
Heavy Duty Drum for 20” to 24” ID Coils with Filler Pads for Up to 30” ID (Nominal 20” ID)
150 HP DC 650/1950 RPM, 500V Reliance Motor (Modern)
Exit Coil Car, 63" Wide Bed
Holding Finger Design for Narrow Slit Coils
(Optional) 60,000# Capacity Two-Arm Turnstile - $39,500
Wide Slots for C-Hook Coil Removal or Hydraulic Pushoff to Banding Line
Full Complement of Shimless Tooling Included for Any Slit Width (Cost New $200,000)
1. Knives
a. 36 pcs @ .750” tk x 15.50” OD
b. 33 pcs @ .750” tk x 16.00” OD
c. 42 pcs @ .500” tk x 15.75” OD
2. Spacers
a. 85 pcs @ 2.000” wide x 12” OD
b. 55 pcs @ 1.000” wide x 12” OD
c. 36 pcs @ 0.500” wide x 12” OD
d. 34 pcs @ 0.300” wide x 12” OD
e. 25 pcs @ 0.200” wide x 12” OD
f. 45 pcs @ 0.164” wide x 12” OD
g. 30 pcs @ 0.155” wide x 12” OD
h. 44 pcs @ 0.132” wide x 12” OD
i. 36 pcs @ 0.125” wide x 12” OD
j. 52 pcs @ 0.116” wide x 12” OD
k. 40 pcs @ 0.108” wide x 12” OD
l. 50 pcs @ 0.104” wide x 12” OD
m. 50 pcs @ 0.102” wide x 12” OD
n. 40 pcs @ 0.101” wide x 12” OD
o. 40 pcs @ 0.100” wide x 12” OD
p. 18 pcs @ 0.060” wide x 12” OD
q. 20 pcs @ 0.030” wide x 12” OD
r. Various shims from .030” to .005” thick
3. Overarm Tooling
a. Full Complement
4. Various Sized Rubber Stripper Rings
HYDRAULICS: Hydraulic pump and tank unit, 40 HP @ 1,000 PSI
ELECTRICAL: AC to DC with PLC controls and new AC to DC transformer
