Maximum Coil Width: 76"

3 Arm Turnstile, Coil Car, Uncoiler, Peeler/Pinch Roll/Shear Unit, Feed Table, Slitter Head, 74" Wide x 6" Diameter Arbor (2 Heads), Recoiler, 2 Arm Turnstile, 78" with Push Off

Year 2004

Thickness Range: .187" - .015"

Line Speed: 1000 FPM

Coil Storage Rack, Coil Car, Mandrel Uncoiler, Peeler Table, Crop Shear, X-Ray Gauge, 2 Injector Slitter Heads, 9" Dia Arbors, 200 HP DC Drive, Rotary/Drag Board Tension Stand, Quick Change Design, Neopreme Rolls, 3M Rolls, Exit Crop Shears, Recoiler, 250 HP DC Drive, Exit L-Type Coil Car, 4 Arm Exit Turnstile, Allen Bradley Digital Drives, PLC Controls, Shimless Tooling

COIL WIDTH.............. 6" - 72"
ARBOR .................. 8"
COIL WEIGHT............. 65,000LBS.
GAUGE................... .0185" - .135"
2 INJECTOR HEADS
2 SPEED LINE 500/1000 FPM
 
 DESIGNED TO RUN AS "TIGHT LINE" OR UTILIZING PIT
 

Make:  Cincinnati
Coil Weight: 60,000Lbs
Coil Width: 12"-72"
Coil ID: 20"/24"
Coil OD: 72"
Line Direction: Left to Right

3-arm Entry Turnstile: 60,000Lbs per arm, Entry Coil Car, Mandrel Uncoiler: 18"-24" (pads for 26"&28"), Peeling Table, Nova Hydraulic Crop Shear, Slitting Head: Arbor Size: 10", Two (2) Scrap Winders, 84" Coil Recoiler, Exit 2-arm Turnstile

72" WIDE
40,000 LB. CAPACITY
3/16" MAXIMUM THICKNESS
LINE SPEED: 150 & 450 FPM BARE DRUM
LINE DIRECTION: RIGHT TO LEFT

COIL CAR, UNCOILER, SLITTER, 8" DIA. X 74" W ARBOR, RECOILER, 2 ARM TURNSTILE, SINGLE SCRAP WINDER

Year 1994

Introduction: This equipment is designed to receive, load, payout, gauge thickness, cut crop, slit, scrap wind, strand extend or mult tension, separate, reciol and deliver steel coils.

Thickness: .015" Min. - .135" Max. Width: 72" Max, Receives/Delivers Coils (ID): 20"/24" Nominal, Receives Coils OD: 84" Max. - 36" Min. Delivers Coils OD: 84" Max. - 33" Min. Weight: 60,000 lbs. Hand: Right, Two (2) Speed Line: 500 FPM with Coil Build-Up to 900 FPM & 1200 FPM, Gauge Control: Loral, Entry Side

Year 1983
Serial No. 11628

Thickness Range:  .037" - .375"
Coil Capacity:  50,000#
Max Coil Width;  72" Trimmed 74" Untrimmed
Coil OD:  72"
Coil ID  20" - 24"
Line Speed:  150 FPM and 450 FPM "Bare Drum"
Line Direction:  Right to Left

Slitting Capacities:
5 Cuts of .375"
12 Cuts of .250"
21 Cuts of .109"

Coil Weight Entry & Exit: 40,000lbs
Thickness: .012" to .115"
Line Speed: 400 FPM & 800 FPM (1,200 FPM by Coil Build Up)
Line Direction: Left to Right

Entry 4 Arm Turnstile, 40,000lbs Entry L-Type Coil Car, Mandrel Uncoiler, North American Edge Control Unit, 2 Scrap Winders, Peeler Table, 2 Sets of Edge Guides, (2) Slitter Heads, 6.5" Diameter Arbor, 75HP DC Drive, 1150/2300 RPM, Pit Cross-Over Table, Double Drag Board Tension stand, Recoiler, 20" Diameter Drum, Hydraulic Push-Off, 100HP DC Motor, 650/1950 RPM, Exit L-Type Coil Car, 40,000lbs Coil Weight, Exit 4 Arm Turnstile, Large Amount of Shimless Tooling and Spare Parts, Allen Bradley PLC, Upgraded Controls SSD Drives, Complete Line with Hydraulics, Electrics, Manuals and Controls

Year 1985
Thickness Range: .135" - .010"
Line Speed: 400 - 1200 FPM

Complete Line with:
L-Type Coil Car, Mandrel Uncoiler, Slitter Entry Unit, Peeler Table, Entry Crop Shear, 2 Injector Style Slitter Heads, Arbor Size: 7" Dia., 125 HP DC Motor, Looping Pit Cross Over Table, Scrap Winder, Combination Drag Board and Rotary Tension Stand, Recoiler, 20" Diameter Hydraulic Drum, 100 DC Motor, Exit L-Type Coil Car, 2 Arm Exit Turnstile, Complete Line with Tooling, Electrics, Hydraulics and Control