International Metalworking Machinery Dealer

 

Used Slitters For Steel Processing

A slitting line is used to break down master coils into smaller coils of a particular width, that an end user such as a metal stamper, tube producer, rollforming house can use in its production of some type of finished good.  Slitters range from 8" in width to 84", master coil weights can range from 3,000# to 80,000#.  Flat rolled steel can be produced up to 7/8" thick to .006 specialty metals. Speed ranges can be up to 2,000 feet per minute, or as low as 100 feet per minute, depending on the desired processing. Galaxie is one of the Worlds largest re-seller of second hand slitting lines.  We sell popular we known brands such as Braner, Pro-Eco, Herr-Voss, and Stamco. We also offer retro fitting services of upgrading older design lines, with new electrical packages, and conversion from pull through to loop lines. 

Please call or email your Galaxie representative today with your requirements, or if you need help, we would be glad to help you sort through the maze of choices.  Why buy new when you can get experienced steel slitting lines, offering solid performance at a lower price? Below is our current inventory of used slitters . . .

Slitting Lines

40" x 8"x 20,000# Cauffiel Slitting Line

101592.jpg

Mandrel Uncoiler, 20" Coil ID, 72" Coil OD, Sliding Base, Peeler Hold down Roll, Slitter Head, 8" Arbors, 40" Arbor face, 2 Inboard bearing housings, 2 sets edge guides, Scrap winder with Oscillating wind, Recoiler, 20" Drum, 46& Drum face, 100 HP AC Drive / 1770 RMP / 230/460 Volt. Overarm Seperator. 2 Hydraulic Units, Starter Panels, Tooling, Knives, Rubbers and Spac

36" x .134" x 20,000lbs Loopco Slitting Line & Banding Line

P9100155.JPG

Complete Line with the Following:4 Arm Entry Turnstile, L-Type Entry Coil Car, 20,000lbs Weight Capacity 40" Coil Width Self Contained Hydraulics.
Mandrel Uncoiler 16" -20" ID 36" Mandrel Face Hydraulic Expansion.
Slitting Head #1 (Ring Design) 38" Arbor Face 5" Arbor Diameter
Thickness Capacity: .015"- .134"20HP DC Motor. Slitting Head #2 36" Arbor Face 5" Arbor Diameter
Pit Cross Over Table

Tension Stand, Scrap Winder

Recoiler Weight Capacity: 15,000lbs 16" ID60HP DC Motor

L-Type Exit Coil Car 20,000lbs Weight Capacity, 2 Arm Exit Turnstile

Complete Line with: Hydraulics, Electrics,Controls and Large Amount of Tooling

36" x .250" x 30,000# Loopco Heavy Gauge Slitting Line

IMG_0548.JPG

Thickness Range:  .015" - .250"
Coil Capacity:  30,000Lb
Coil ID:  20" - 24" Entry & 20" Exit
Coil OD:  72"
Coil Width:  .500" - 37"

Entry 3 Coil Storage Ramp, L-Type Coil Car, Mandrel Uncoiler, Loopco Peeler / Hold Down Roll, Crop Shear, Loopco Slitter Head, Swinger Head Design, 6" Dia Arbors, 2 Sets of Edge Guides, Shimless Tooling, Scrap winder, Recoiler, 20" Dia Drum, 40" Drum Face, 100 HP DC Drive, 2 Speed Gear Box, Overarm Seperator, 1 Arm Exit Turnstile, Complete Line with Electrics, Hydraulics, Controls, Shimless Tooling, and NEW Rubbers

36" x 20,000Lbs Loopco Loop Slitting Line

1.JPG

Make: Loopco
Width: 36"
Weight: 30,000Lbs entry / 20,000Lbs exit
Direction: Right to Left

30,000 lbs L-Type Coil Car, Mandrel Uncoiler: ID: 16"- 20" (Pads for 24"), Weight: 30,000Lbs, Hydraulic Hold-Down Roll, Peeling Table, Slitting Head: Arbor Diameter: 5", Drag-Board Tension Stand, Recoiler: ID: 16", Weight:20,000Lbs, MICO Scrap Winders, Oscilating Wind, 2-Arm Exit Turnstile, C-Hook Slot, Powered Push-Off

36" x 15,000# Seco / Torrington Slitting Line

101657a.jpg

Thickness: .010" - .187". Line Speed: 175 - 1200 fpm. Complete Line with: Entry 2 arm turnstile. 30,000# Pro Eco Coil Car. Mandrel Uncoiler. Loopco peeler hold on roll. Torrington Slitter Head, 38" arbor face, 6" dia face. Scrap winder. Recoiler, hydraulic drum, Horsburg Scott gearbox ratio: 14.3 to 1, 125/150 HP DC motor. Exit 2 arm turnstile. Shimless tooling. Complete line with hydraulics, electrics, and controls.

27" x .157" x 12,000# Durmech Loop Slitting Line

101639.jpg

Make: Durmech. Coil Width: 700mm. Coil Weight: 6ton. ID: 813mm / OD: 1727mm. L-Type Coil Car, self contained hydraulics. Mandrel Uncoiler, hydraulic sliding base, powered hold down roll, water cooled brake. Peeleing table, powered pinch rolls, edge guiding unit. Two (2) Slitting Heads, 4.5" Arbor Size, 74Kw DC Motor. Looping Pit Cross Over Table, Two (2) Scrap Winders, Drag / Rotary Combo. Coil Crop Shear, powered pinch rolls. Recoiler, hydraulic drum, hydraulic push off, over-arm seperator, 89.5Kw DC motor. Exit L-type Coil Car.

24" Reusch Precision Loop Slitting Line

DSC_0421.JPG

Ring Slitter Design

Thickness Range:  .012" -.202"
Line Speed:  0 - 500 FPM
Coil Capacity:  20,000#
Coil ID:  16" - 20" Pads for 24"
Coil OD:  60"
Line Direction:  Left to Right

Mandrel Uncoiler, Hold Down Roll, Peeler Table, Crop Shear, Pinch Rolls, Coil Breaker,Slitter Head,Ring Slitter Design,5 1/2" Dia Arbors,75 HP DC Drive.2 Scrap Choppers with Helical Blades,Tension Stand,Recoiler,Overarm Seperator,Shimless Tooling (Very Large Quantity) Electrics, Hydraulics and Controls

18" Bigwood Slitter

DCP_0242.JPG

Uncoiler - 14 to 20 I.D., Non-powered, Drag brake; Slitter - Capacity ¼ x 18 Mild Steel,  7" (288mm) Diameter Arbors, 21"(533) Face, Crofts Gear Reducer, 76:1 Ratio, 50 H.P.

New Arrivals

Current Brochure


Members of the Turnaround Management Association

Site Updated: September 10, 2010