Used Slitters For Steel Processing

A slitting line is used to break down master coils into smaller coils of a particular width, that an end user such as a metal stamper, tube producer, rollforming house can use in its production of some type of finished good. Slitters range from 8" in width to 84", master coil weights can range from 3,000# to 80,000#. Flat rolled steel can be produced up to 7/8" thick to .006 specialty metals. Speed ranges can be up to 2,000 feet per minute, or as low as 100 feet per minute, depending on the desired processing. Galaxie is one of the Worlds largest re-seller of second hand slitting lines. We sell popular we known brands such as Braner, Pro-Eco, Herr-Voss, and Stamco. We also offer retro fitting services of upgrading older design lines, with new electrical packages, and conversion from pull through to loop lines.

Please call or email your Galaxie representative today with your requirements, or if you need help, we would be glad to help you sort through the maze of choices. Why buy new when you can get experienced steel slitting lines, offering solid performance at a lower price? Below is our current inventory of used slitters . . .

Slitting Lines

84" x .313" x 40,000# Delta Slitting Line

Year 1982
Material Hot Rolled & Oiled, Cold Rolled Galvanized
Shear Strength 55,000 psi
Max. Untrimmed Width 86”
Max. Trimmed Width 84”
Max. Coil Weight 40,000 lbs
Max. Coil O.D. 72”
Min. Coil O.D. 32”
Entry Coil I.D. 20” & 24”
Exit Coil I.D. 20”

Thickness: .020" - .313"

Speed Low 75 - 225 FPM & High 150 - 450 FPM

Complete Line With:

L-Type Coil Car, Mandrel Uncoiler, Peeler, Slitting Head with 8" Dia Arbors, Sliding Outboard Housing, Scrap Winder, Recoiler, 2 Speed Gear Box, 75 HP DC Drive, Exit 2 Arm Turnstile, Electrics, Hydraulics and Controls, Tooling, Knives, Rubbers, Spacers, Knives – 2 Sets 1.000”, one of 0.750”, 2 of 0.500” and one 0.250”

80" x 50,000lbs Heavy Gauge L.A.S.A Slitting Line

Year: 1997

Cutting Capacity: 10 cuts of 10mm
Coil ID: 480mm-630mm (19"-25")
Coil OD:2,300mm ( 90")

Speed of Line:
75m/min - 5 to 10mm
150m/min - 1 to 5mm
Line direction: Left to Right

Entry Coil Car, 25 MT Mandrel Uncoiler, Peeler/Driver Hold, Edge Guide Control Unit, 5 Roll Flatener, Crop Shear, (2) Slitting Heads, Scrap Baller, Combination Rotary/Drag Board Tension Stand, Recoiler, Exit Coil Car, 2 Arm Turnstile, Tooling, Electrics, and Hydraulics

78" (2000mm) x .157" (4mm) x 20,000Lbs Proin/Fagor Loop Slit

Make: Proin
Material: HR, CR, Galvanized, Pickled
Thickness: .4mm - 4mm
Width: 2000mm
ID: 600mm-700mm
OD: 1800mm

Entry Coil Car, Mandrel Uncoiler, Peeling Unit, Powered Pinch Rolls, Edge Guide Unit, 4-Hi Precision Leveler, Two (2) Slitting Heads, Scrap Baller, Pit Cross-Over Table, Drag-Board Tension Stand, Strip Recoiler, Leveler Motor: 120Kw DC, Recoiler Motor: 120Kw DC, Complete Line with Electrics, Hydraulics, Controls, Tooling

72" x .375" Paxson Loop Slitting Line with 2 Heads

Year 1983
Serial No. 11628

Thickness Range: .037" - .375"
Coil Capacity: 50,000#
Max Coil Width; 72" Trimmed 74" Untrimmed
Coil OD: 72"
Coil ID 20" - 24"
Line Speed: 150 FPM and 450 FPM "Bare Drum"
Line Direction: Right to Left

Slitting Capacities:
5 Cuts of .375"
12 Cuts of .250"
21 Cuts of .109"

72" x .250" x 60,000# Cincinnati Slitting Line

Pull Through Line

4 Arm Entry Turnstile, Entry L-Type Coil Car, Mandrel Uncoiler, 4 Leaf Hydraulic Expansion, Peeler Table, 2 Slitter Heads, 7" Dia Arbors, Cross Over Table, 2 Scrap Winders, Recoiler, 20" Dia Drum, Overarm Seperator, Exit L-Type Coil Car, Floor Standing / Self Contained Hydraulics, Tooling, Electrics, and Hydraulics

72" x .500" 60,000 Lbs Cincinnati Slitting Line

Make: Cincinnati
Coil Weight: 60,000Lbs
Coil Width: 12"-72"
Coil ID: 20"/24"
Coil OD: 72"
Line Direction: Left to Right

3-arm Entry Turnstile: 60,000Lbs per arm, Entry Coil Car, Mandrel Uncoiler: 18"-24" (pads for 26"&28"), Peeling Table, Nova Hydraulic Crop Shear, Slitting Head: Arbor Size: 10", Two (2) Scrap Winders, 84" Coil Recoiler, Exit 2-arm Turnstile

72" X 3/16" X 40,000 Lbs DELTA SLITTING LINE

72" WIDE
40,000 LB. CAPACITY
3/16" MAXIMUM THICKNESS
LINE SPEED: 150 & 450 FPM BARE DRUM
LINE DIRECTION: RIGHT TO LEFT

COIL CAR, UNCOILER, SLITTER, 8" DIA. X 74" W ARBOR, RECOILER, 2 ARM TURNSTILE, SINGLE SCRAP WINDER

72" x .135" x 60,000# Herr Voss Loop Slitting Line with Injector Heads

Year 1994

Introduction: This equipment is designed to receive, load, payout, gauge thickness, cut crop, slit, scrap wind, strand extend or mult tension, separate, reciol and deliver steel coils.

Thickness: .015" Min. - .135" Max. Width: 72" Max, Receives/Delivers Coils (ID): 20"/24" Nominal, Receives Coils OD: 84" Max. - 36" Min. Delivers Coils OD: 84" Max. - 33" Min. Weight: 60,000 lbs. Hand: Right, Two (2) Speed Line: 500 FPM with Coil Build-Up to 900 FPM & 1200 FPM, Gauge Control: Loral, Entry Side

60" x .250" Cincinnati Loop Slitting Line with 2 Heads

Thickness Range: .018" - .250"
Coil Capacity: 50,000# Coils
Line Speed: 130 FPM, 260 FPM, 440 FPM
Strip Width: .625" - 60"
Coil ID: 20" - 24"
Coil OD: 72"

3 Arm Turnstile, L-Type Coil Car, Mandrel Uncoiler, Peeler, Pinch Rolls, Crop Shear, Edge Guides, 2 Slitter Heads, 7" Dia Arbors, 125 HP DC Drive, Hydraulic Sliding Outboard, 2 Scrap Winders, Looping Pit Cross Over Table, Drag Board Tension Stand, Exit Crop Shear, Recoiler, Full Hydraulic Chrome Drum, 3 Speed Gear Box, 75 HP DC Drive, 2 Arm Exit Turnstile, Complete Line with Hydraulics, Electrics, and Controls, CMC Solid State Drives, Unoiler Upgraded in 1996 to 50,000#, Recoiler New Aeromet Drum in 1998, Shimless Tooling

60" x .125" x 50,000# Pro Eco Loop Slitting Line with Kor Flex Leveler Year 1995

Year 1995

Thickness Range: .015" - .125"
Coil Weight Capacity: 50,000#
Line Direction: Right to Left
Enty & Exit Coil ID: 20" - 24"
Entry & Exit Coil OD: 72"
Coil Width: 62" - 12"
Line Speed: 750 FPM
Max Shear Strength: 48,000 PSI

Complete Line with:

4 Arm Entry Turnstile ,L- Type Coil Car, Mandrel Uncoiler,150 HP DC drag generator brake,Powered hold down roll,North American edge control,Peeler / Pinch Rolls / Crop Shear Unit

2 Injector Slitter Heads,7 1/2" Dia arbors,150 HP DC drive,Turntable for slitter head change

International Metalworking Machinery Dealer

Section Links

Current Inventory

Additional PDFs