Line Speed: 2000 FPM, Material Thickness: .229" - .010", 20" Coil I.D., 78" Coil O.D., 1.85:1 Main Gear BU8 Ratio, 2-1085 H.P. DC Motors, 650 Volt, In Tandem, Outboard Bearing Support, Entry & Exit Coil Cars, Numerous Spare Parts.

Width, Entry Coil: 23 1/2" - 60", Delivery Coil: 23 1/2" - 60"
I.D.,  Entry Coil: 24", Dleivery Coil: 24"
O.D.,  Entry Coil: 66", Delivery Coil: 66"
Weight, Entry Coil: 55,000#, Delivery Coil: 50,000#
Gauge: .024" - .074"

Pay-Off Reel (Cone Type), Mill Stand, Tension Reel, Screwdowns, Backup Bearings, Work Roll Bearings, A.I.S.I Rated Capacity - 393,000 net tons, Hydraulic roll shaping installed in 1964

Thickness Range from .005” - .160”, Line Speed 1060 FPM, Main Mill Drive 600 HP DC,Winders 500 HP DC, Hydraulic Screw Downs, Vollmer Thickness Gauges, 1.578” Dia Work Roll, 19” Maximum Strip Width, Complete Mill.

Manufacture: Fenn (USA)
Year of Manufacture: 1976 
Reconditioned in 1989
Full operation until May 2006
For Carbon and Stainless Steel Coils
Work rolls dia (Nominal): 1.26" (32mm)
 
Pay off, Leveler, Left & right winder, Mill stand, Rewinding payoff, Rewinder, Oil celler, Electrical parts

Year Built:  2000
Material:  Stainless Steel, Titanium, Aluminum*, Ni-Allows, and Carbon Steel
Strip Width:  14" Maximum, 7-7/8" Minimum
Strip Thickness Entry:  0.030" Maximum
Strip Thickness Exit:  0.001" Minimum
Coil Weight:  3,000 lb. Maximum
Payoff Coil: I.D.: 16", O.D.: 40"
Winder Coil: I.D.: 20", O.D.: 42"
Re-Winder Coil: I.D.: 16", O.D.: 40"
Mill Size:  ZR24-14 Sendzimir
Mill Speed:  0/450/800 FPM
Line Direction:  Right to Left
Mill Power:  250 HP @ 0/650/1300 RPM
Winder Power:  200 HP @ 0/500/1500 RPM
Strip Tension: 11,785 Lbs. to 560 FPM, 8,250 Lbs. to 800 FPM, 300lbs Min Tension
Coolant System:  175 GPM

Thickness Range:  2.2mm - .8mm (.087" - .031") , Speed:  200 MPM (660 FPM), Strip Width 200mm - 50mm (8" - 2")  

Back Up Roll 250mm Dia x 250mm Face, Work Roll 101mm Dia x 250mm Face, AGC Gauge Control, Entry & Exit Contact Gauges,

Complete Mill With:  Entry Turnstile, Double End Uncoiler, #1 and #2 4 Hi Mill Stands with 110 KW DC Drive, Tension Measuring Roll, Recoiler with 75 KW DC Drive, Exit Turnstile, Roll Changing Sled, Roll Grinder, Paper Filteration System, Coolant Pumps and Valves, Electrical Drive Panels and Controls, Spare Rolls and Chocks, Spare Parts, NEW CONDITION. 

Year:  1998/9
3 Stands
Roll Size:  11.5" Diameter x 6.5" face rolls
-each stand w/30 HP DC motor
-maximum reduction:  .010" @ 4" to 6" wide
-maximum reduction:  .012" @ 4" and under

Stock sizing machine
-6" maximum stock width
-.032" to .150" thick
-entry passline rolls
-entry guide rolls, (2) sets, manual adjustment
-20 to 200 FPM variable line speed
-(3) 30 HP "us motors" DC motors w/blowers, 1750/2300 RPM, 500V
-(3) Textron cone drive reducers w/20:1 reduction ratio

The mills are complete with operator consoles, and all drawings.